Company:Lambretta Model D

From HandWiki
Short description: Scooter built by Lambretta
Lambretta Model D
Lambretta 150 d.JPG
Lambretta Model D 150
ManufacturerLambretta
Parent companyInnocenti
Production
  • 125D: 1951-1956
  • 150D: 1954-1956
PredecessorModel C
SuccessorLi Series 1
ClassScooter
Engine
Bore / stroke
  • 125D: 52 mm × 58 mm (2.0 in × 2.3 in)
  • 150D: 57 mm × 58 mm (2.2 in × 2.3 in)
Compression ratio1:6.5
Top speed
  • 125D: 47 mph (76 km/h) @ 4,600rpm
  • 150D: 55 mph (89 km/h) @ 4,800rpm
Power
  • 125D: 5 hp (3.7 kW)
  • 150D: 6 hp (4.5 kW)
Ignition typePoints Ignition System
Transmission3-speed handlebar twistgrip, Shaft drive
Frame typeSteel Tubular Frame
Suspension
  • Front: Spring Suspension
  • Rear: Torsion Bar
Brakes
  • Front: Finned aluminium drum brakes
  • Rear: Finned aluminium drum brakes
Tyres4.00*8
DimensionsL: 1,770 millimetres (70 in)
W: 740 millimetres (29 in)
H: 960 millimetres (38 in)
Weight
  • 125D: 70 kilograms (150 lb)
  • 150D: 75 kilograms (165 lb)
 (dry)
Fuel capacity5.6 + 0.7 L (1.23 + 0.15 imp gal; 1.48 + 0.18 US gal)
Fuel consumption141 mpg‑imp (2.00 L/100 km; 117 mpg‑US)

The Lambretta Model D was a scooter produced by Lambretta as a direct replacement for the Model C. The Model D was the first Innocenti scooter to be manufactured outside of Italy as the licence was sold in Europe, Asia and South America.[1]

Model D Design

Frame and Body

The Model D had a revised steel tubular frame that had been lengthened to make way for new suspension and other small updates.[2] The basic layout of the Model C was kept with a fuel tank under the front seat and a toolbox at the rear of the bike. The front suspension tubes were fully enclosed to hide the spring suspension and hermetically sealed in oil to protect from corrosion.[2] Rear suspension was provided by torsion bar that attached to the engine and frame with the engine pivoted at the front and being used as a swing arm.[3] Early engine mounts (1951 to mid-1952) were just bearings, in mid-1952 they were changed to Silent Blocs to help reduce vibration.[4] A headlamp was attached to the front of the frame with underneath the bicycle styled chrome steel handlebars.[4] A round brake light was attached at the rear of the bike just above the number plate. Brakes were provided by aluminium finned drums with the front being cable operated and the rear rod operated, by a pedal located on the right floor panel.[3] The tyres were 4.00* 8 came out of the factory provided by Italian manufactures Pirelli or CEAT.[5]

Later versions included adjustable aluminium handlebars, plastic levers, lock for toolbox lid, ivory and later white plastic light switch, provisions for a rear damper to be fitted and grab handles on the rear saddle.[4]

Engine and transmission

The 123cc engine and transmission was upgraded and simplified in an attempt to improve reliability as well as improving the ride of the scooter.[2] The top end kept the same construction with the cylinder made of cast iron and head aluminium but the cooling system was enlarged to make the bike more reliable in heat and under strain.[3] The new Carburetor was a Dell'Orto MA18. The transmission provided by a 3-speed gearbox and was shaft driven. The exhaust was revised to reduce noise and vibration.[2] In 1954 due to demand from the public, for a larger engine, the Model D150 was announced with a 148cc engine. The overall top speed was improved slightly but the main area of improvement was in torque and gear ratios to make the ride smoother and to help the scooter make it up mountain passes.[6]

Electrics

The electrics on a Model D were, basic the ignition being provided by contact points and the lights and horn were provided by 6 volt electrics. Later models could have an electric start fitted as an extra, controlled by a small plastic lever on the handlebars.[2]

Paint and finish

The 125D came in 3 Lechler system body colours Olive green 8021, Light chamois 8055 and Sand beige 8029. Engine and frame were painted in Aluminium Fiat 690. Early saddles were brown imitation leather but in 1954 the colour was changed to green.[4] The 150D came only came in 2 colours Sand beige 8029 and a few examples from 1956 came in Light grey 8012. Engine and frame were once again painted in Aluminium Fiat 690.

LD Design

Lambretta Model LD
Lambretta LD 125 (1956) 20120211.jpg
Lambretta Model LD 125
ManufacturerLambretta
Parent companyInnocenti
Production
  • 125LD: 1951-1958
  • 150LD: 1954-1958
PredecessorModel C
SuccessorLi Series 1
ClassScooter
Engine
Bore / stroke
  • 125LD: 52 mm × 58 mm (2.0 in × 2.3 in)
  • 150LD: 57 mm × 58 mm (2.2 in × 2.3 in)
Compression ratio1:6.5
Top speed
  • 125lD: 47 mph (76 km/h) @ 4,600rpm
  • 150lD: 55 mph (89 km/h) @ 4,800rpm
Power
  • 125LD: 5 hp (3.7 kW)
  • 150LD: 6 hp (4.5 kW)
Ignition typePoints Ignition System
Transmission3-speed handlebar twistgrip, Shaft drive
Frame typeSteel Tubular Frame
Suspension
  • Front: Spring Suspension
  • Rear: Torsion Bar
Brakes
  • Front: Finned aluminium drum brakes
  • Rear: Finned aluminium drum brakes
Tyres4.00*8
DimensionsL: 1,770 millimetres (70 in)
W: 740 millimetres (29 in)
H: 960 millimetres (38 in)
Weight
  • 125LD: 85 kilograms (187 lb)
  • 150LD: 88 kilograms (194 lb)
 (dry)
Fuel capacity5.6 + 0.7 L (1.23 + 0.15 imp gal; 1.48 + 0.18 US gal)
Fuel consumption141 mpg‑imp (2.00 L/100 km; 117 mpg‑US)

The Lambretta LD was launched as a direct replacement for the LC luxury models of Lambretta and was essentially a Model D with Leg Shields, running boards and side panels to provide improved protection from weather and the dirty components of the scooter.

Frame and Body


The LD was almost exactly the same as the Model D in frame and engine. The body leg-shields, horncast, running boards and side panels. Side panels had 2 chrome ring portholes near the rear of the bike. The extra panels added 15 kg (33 lbs) to the overall dry weight of the LD125. Other than a few differences, such as an Innocenti badge located on the headlight and Lambretta badge in aluminium on the leg-shield, the 125D and 125LD were identical. Later versions included oval panel hole, replacing the 2 portholes, with plastic vent grills, plastic badge on the leg-shields larger saddles with dark green leather covers and a larger air-filter.[5]

Engine and transmission

The engine remained the same as that found in the Model D.

Paint

Paint was also the same as the Model D, but in 1953 the LD125 only came in Sand beige 8029.

References

  1. "Lambretta MK D". https://www.lambretta.com/classics/mk-d/. 
  2. 2.0 2.1 2.2 2.3 2.4 Tessera, Vittorio (1995). Innocenti Lambretta: The Definitive History With Restoration Guide. Giorgio Nada Editore. pp. 75–79. 
  3. 3.0 3.1 3.2 "LCGB Model D". http://www.ilambretta.co.uk/lambrettascooters/modeld.html. 
  4. 4.0 4.1 4.2 4.3 Tessera, Vittorio (1995). Innocenti Lambretta: The Definitive History with Restoration Guide. Giorgio Nada Editore. pp. 246–249. 
  5. 5.0 5.1 Tessera, Vittorio (1995). Innocenti Lambretta: The Definitive History with Restoration Guide. Giorgio Nada Editore. pp. 230–231. 
  6. Tessera, Vittorio (1995). Innocenti Lambretta: The Definitive History with Restoration Guide. Giorgio Nada Editore. pp. 85–95.